Version
|
Highlights
|
LUNA Firmware
1.00.4547
MADRIX Version
MADRIX 3.0
Release Date
July 2013
|
▪Initial firmware release. |
LUNA Firmware
1.01.4555
MADRIX Version
MADRIX 3.1
Release Date
November 2013
|
▪Improved functionality and communication with the MADRIX 3 Software. |
LUNA Firmware
1.02.4946
MADRIX Version
MADRIX 3.2
Release Date
March 2014
|
▪Added support for LUNA 4 and LUNA 16 in addition to LUNA 8. |
LUNA Firmware
1.03.5043
MADRIX Version
MADRIX 3.3
Release Date
November 2014
|
▪Optimized device reply time (Poll Reply) to ensure that all connected devices are found when searching for them automatically in MADRIX 3.
▪Fixed an issue that would reset the network settings with the next start when a Subnet Mask higher than 255.255.255.0 was set up.
▪Fixed issues with sending out data when receiving Art-Net data from two sources.
▪Fixed an issue that only used the last of DMX output ports to send out data when several ports had been assigned the same Art-Net universe. |
LUNA Firmware
1.04.5298
MADRIX Version
MADRIX 3.3a
Release Date
December 2014
|
▪Fixed an issue that the IP address could not be changed using the web configuration tool. |
LUNA Firmware
1.05.5501
MADRIX Version
MADRIX 3.4
Release Date
June 2015
|
▪Fixed that the Poll Reply only returned 4 ports for LUNA 8 or LUNA 16. |
LUNA Firmware
1.05.5997
MADRIX Version
MADRIX 3.6
Release Date
May 2016
|
▪All built-in status LEDs can now be switched off over Art-Net via ArtAdress.
▪Added support for ArtSync. |
LUNA Firmware
1.05.6298
MADRIX Version
MADRIX 3.6b
Release Date
September 2016
|
▪Web configuration page: Added the Refresh button to always show the latest information that was last saved on the device in the web browser (instead of using a browser refresh which may change settings again). |
LUNA Firmware
1.05.6996
MADRIX Version
MADRIX 3.6d
Release Date
December 2016
|
▪Fixed an issue for LUNA 4 that returned an incorrect BindIndex after receiving a PollReply. |
LUNA Firmware
1.06.7074
MADRIX Version
MADRIX 3.6h
Release Date
February 2018
|
▪Added 4 distinct options for sending data output in case of data connection loss [only available in the web configuration tool]:
- Send The Last Received Frame Continually
- Send Black Frames Continually
- Stop Sending After Sending A Black Frame
- Stop Sending
▪Increased the minimum output frequency that is sent on each port from 10 FPS to 20 FPS [in order to ensure functionality with lighting fixtures that are not functioning well with low frame rates]. |
LUNA Firmware
1.06.7104
MADRIX Version
MADRIX 5.0
Release Date
May 2018
|
▪Added BindIdx 3 to the PollReply to better communicate the additional DMX-IN port. |
LUNA Firmware
1.06.7106
MADRIX Version
MADRIX 5.0a
Release Date
June 2018
|
▪Web configuration page: Updated the visual appearance for MADRIX 5.
▪Web configuration page: Art-Net universes are now also shown in hexadecimal notation in addition to the decimal notation. |
LUNA Firmware
1.06.7134
MADRIX Version
MADRIX 5.0c
Release Date
July 2018
|
▪Web configuration page: Updated the MADRIX Logo.
▪Web configuration page: Renamed Direct IP Mode to Unicast Mode. |
LUNA Firmware
1.06.7148
MADRIX Version
MADRIX 5.0d
Release Date
August 2018
|
▪Fixed a critical issue that could halt the device in rare cases. |
LUNA Firmware
1.06.7172
MADRIX Version
MADRIX 5.0e
Release Date
February 2019
|
▪Web configuration page: Fixed a critical issue that discarded the current setting for In Case Of Data Connection Loss when disconnected from power and automatically reset to the default value again. |
LUNA Firmware
2.00.7232
MADRIX Version
MADRIX 5.1
Release Date
May 2019
|
▪Added support for Streaming ACN / sACN.
▪Added a Channel Offset for each output port.
▪For every single universe, a single ArtPollReply packet is being sent to reply to Art-Net polls (#3841).
▪Web configuration page: Universes are now shown in hexadecimal notation and Art-Net Net switch / sub-net switch notation in the Network Universe tooltips.
▪Fixed an issue that did continue to send the last frame that was received over USB under certain circumstances although new network data was received.
▪Fixed an issue that only allowed answering ping requests up to 32 byte.
▪Fixed an issue that did not send with the correct frame rate and timeout setting when having received ArtSync packages prior. |
LUNA Firmware
2.00.7254
MADRIX Version
MADRIX 5.1a
Release Date
August 2019
|
▪Fixed an issue that could prevent uploading the bootloader correctly.
▪Fixed an issue that did not allow to call the built-in web configuration page via the MADRIX Device Configuration window. |
LUNA Firmware
2.00.7261
MADRIX Version
MADRIX 5.3
Release Date
May 2020
|
▪Fixed an issue that produced incorrect DMX-IN packages in MADRIX LUNA 16 when receiving data from 2 sources for merging in addition to DMX-IN data. |
LUNA Firmware
2.00.7291
MADRIX Version
MADRIX 5.4
Release Date
December 2020
|
▪Fixed a critical issue that could crash the web configuration when switching to Streaming ACN as network-data source (#6433, #6563).
▪Fixed an issue that could result in random bursts of value 255 being sent on all channels when using Streaming ACN as network-data source (#6631). |
LUNA Firmware
2.01.7292
MADRIX Version
MADRIX 5.4c
Release Date
July 2021
|
▪Web configuration page: Added the option to reboot the device (#7446).
▪Web configuration page: Added the option to reset the device to factory default settings (#7446). |
LUNA Firmware
2.02.7297
MADRIX Version
MADRIX 5.4e
Release Date
October 2021
|
▪During normal operation, quickly pressing the Reset button now sends an Art-Net PollReply and a MADRIX PollReply for device discovery (#7008).
▪Improved and streamlined how the device replies to polls with Unicast, Directed Broadcast, or Limited Broadcast (#7007).
▪Fixed a critical issue that could crash the web configuration and lead to the device not sending ArtIpProgReply packets anymore when setting the IP address via ArtIpProg (#7532). |
LUNA Firmware
2.03.7298
MADRIX Version
MADRIX 5.4f
Release Date
January 2022
|
▪The bootloader can now read the hardware revision/model over USB (#7803).
▪Fixed how ARP requests are executed (#4779).
▪Fixed an issue that would drop output frames when merging from two sources and using DMX-IN at the same time due to insufficient buffers (#5392). |
LUNA Firmware
2.04.7299
MADRIX Version
MADRIX 5.4g
Release Date
March 2022
|
▪Fixed the timing of the data output in combination with UCS512C/SM17500 LED chips (#8024, #8025). |
LUNA Firmware
2.05.7300
MADRIX Version
MADRIX 5.4h
Release Date
April 2022
|
▪Fixed a critical issue that recognized MADRIX LUNA 4 and MADRIX LUNA 16 only as MADRIX LUNA 8 in certain cases (#8275). |
Bootloader
3.00.7310
Release Date
May 2023
|
▪Updated the bootloader system (#9105, #9149, #9571).
▪Status LED power now correctly blinks green (in addition to the logo LED) when a device is in bootloader mode (#9135).
▪The bootloader is able to provide the MAC address and serial number of the device over USB (#9332).
▪The bootloader can now be updated over Art-Net (#9383).
▪The bootloader now provides the hardware revision; which is especially relevant to be able to update devices in bootloader mode via the MADRIX HARDWARE MANAGER (#8905).
▪The bootloader now sends a single Art-Net PollReply without BindIndex after startup and remaining in bootloader mode (#8031).
▪Fixed an issue that did not always respond to firmware packets being sent over Art-Net (#8030).
▪Fixed an incorrect USB descriptor, which caused devices to enumerate for a long time when connected to a USB 3.0 hub (#8238).
▪Fixed an issue that prevented firmware updates over network (#9187). |
LUNA Firmware
3.00.7309
Release Date
May 2023
|
▪Updated the system of the device (#6780, #8053, #8060, #8601, #8738, #8860, #9135, #9148, #9163, #9170, #9180, #9326, #9430, #9538).
▪Added support for Art-Net 4 (#2349).
▪Web Configuration: Added the possibility to edit the ShortName identifier for Art-Net (#8168).
▪Web Configuration: Added automation options for automatic numbering of the Network Universes (#8658). [JavaScript is required.]
▪Web Configuration: Added automation options to set the Network Universe of the first port for all other ports (#9540).
▪Web Configuration: Added automation options to set the Channel Offset of the first port for all other ports (#9186).
▪Web Configuration: Added the option to enable or disable Send Full Frames for all ports at once (#9186).
▪Web Configuration: Now shows the uptime of the device (#8309).
▪Web Configuration: Added the development hash to the firmware version to the Device Information section (#9362).
▪The bootloader version can now be provided by the firmware over USB (#8875).
▪Improved the alignment of spin-button controls in the web configuration (#9166).
▪Improved reliability by ensuring that network settings are always properly saved (#9214).
▪Fixed an issue that did not apply all parameters when setting every single parameter at once for MADRIX LUNA 16 (#9175, #9181).
▪Fixed several issues that could prevent all settings in the web configuration to be saved and available again after a power cycle (#9197).
▪Fixed an issue that did not set the input universe for sACN (#9283).
▪Fixed an issue that did not correctly join and leave universe assignments in case of sACN (#9591). |